Development and validation of an ADDIE-based jobsheet as procedural scaffolding for vocational electrical practice
DOI:
https://doi.org/10.21831/jpv.v16i1.98312Keywords:
ADDIE model, electrical installation, jobsheet, procedural scaffolding, TVET, vocational educationAbstract
Vocational electrical learning requires students to transform technical concepts into safe, ordered, and assessable workshop performance. This study developed and validated an ADDIE-based electrical lighting installation jobsheet as a form of procedural scaffolding for Grade XI students at an Indonesian vocational school. A research-and-development design was implemented using the ADDIE stages of analysis, design, development, implementation, and evaluation, with a one-group development trial. Data were collected through classroom observation, a teacher interview, expert validation, student-response questionnaires, and diagnostic, formative, and summative assessments. Three media experts, three material experts, and 23 students participated. The jobsheet was produced in printed and digital formats and covered five practice units: single-switch installation, series-switch installation, two-way switch installation, distribution-board lighting installation for a simple building, and light-sensor-based lighting installation. Expert validation indicated high feasibility in terms of media quality (M = 3.83/4.00) and material quality (M = 3.84/4.00), while the student response was positive (M = 3.49/4.00). Learning scores increased from diagnostic assessment (M = 47.61) to summative assessment (M = 85.65), with high normalised gain (g = 0.73), a very large paired effect size (Cohen’s dz = 3.02), and 82.61% summative mastery. The findings indicate that a systematically designed jobsheet can connect curriculum outcomes, occupational safety, practical procedures, and assessment evidence. Because the implementation employed a one-group development trial, the findings should be interpreted as evidence of instructional feasibility and associated learning improvement rather than causal effectiveness. The study contributes a low-cost, competency-aligned practical learning resource for vocational electrical education; however, further controlled and multi-site studies are required to verify retention and practical-skill transfer.
References
Afif, T. R. H., & Siregar, M. F. R. (2024). Pengembangan kurikulum analisis kesesuaian SKL, CP, TP, dan ATP dalam Kurikulum Merdeka di SMA/MA. Jurnal Penelitian Pendidikan Indonesia (JPPI), 1(4), 475–485. https://jurnalistiqomah.org/index.php/jppi/article/view/1746?articlesBySameAuthorPage=14
Ainscow, M. (2020). Promoting inclusion and equity in education: Lessons from international experiences. Nordic Journal of Studies in Educational Policy, 6(1), 7–16. https://doi.org/10.1080/20020317.2020.1729587
Akkerman, S. F., & Bakker, A. (2011). Boundary crossing and boundary objects. Review of Educational Research, 81(2), 132–169. https://doi.org/10.3102/0034654311404435
Al Shehri, M. Y. (2004). Current issues in medical education. West African Journal of Medicine, 22(4). https://doi.org/10.4314/wajm.v22i4.28058
Alinier, G. (2007). A typology of educationally focused medical simulation tools. Medical Teacher, 29(8), e243–e250. https://doi.org/10.1080/01421590701551185
Avelino, C. C. V., Borges, F. R., Inagaki, C. M., Nery, M. de A., & Goyatá, S. L. T. (2016). Desenvolvimento de um curso no Ambiente Virtual de Aprendizagem sobre a CIPE®. Acta Paulista de Enfermagem, 29(1), 69–76. https://doi.org/10.1590/1982-0194201600010
Bejan, A., Xi, M., & Parker, D. L. (2020). Outcomes of a safety and health educational intervention in auto body and machine tool technologies vocational college programs: The Technical Education Curricula for Health and Safety (TECHS) study. Annals of Work Exposures and Health, 64(2), 185–201. https://doi.org/10.1093/annweh/wxz092
Bettinger, E. P., Boatman, A., & Long, B. T. (2013). Student supports: Developmental education and other academic programs. The Future of Children, 23(1), 93–115. https://doi.org/10.1353/foc.2013.0003
Billett, S. (2004). Workplace participatory practices. Journal of Workplace Learning, 16(6), 312–324. https://doi.org/10.1108/13665620410550295
Cahyadi, R. A. H. (2019). Pengembangan bahan ajar berbasis ADDIE model. Halaqa: Islamic Education Journal, 3(1), 35–42. https://doi.org/10.21070/halaqa.v3i1.2124
Chen, Y.-F., Luo, Y.-Z., Fang, X., & Shieh, C.-J. (2018). Effects of the application of computer multimedia teaching to automobile vocational education on students’ learning satisfaction and learning outcome. EURASIA Journal of Mathematics, Science and Technology Education, 14(7), 3293–3300. https://doi.org/10.29333/ejmste/91245
Davydenko, V. A., & Chebrovskaya, S. V. (2025). Technology of continuous tutor support for students’ professional self-determination. Perspectives of Science and Education, 77(5), 56–68. https://doi.org/10.32744/pse.2025.5.4
Eeckhout, T., Gerits, M., Bouquillon, D., & Schoenmakers, B. (2016). Video training with peer feedback in real-time consultation: Acceptability and feasibility in a general-practice setting. Postgraduate Medical Journal, 92(1090), 431–435. https://doi.org/10.1136/postgradmedj-2015-133633
Fauzi, S. A., & Mustika, D. (2022). Peran guru sebagai fasilitator dalam pembelajaran di kelas V sekolah dasar. Jurnal Pendidikan dan Konseling (JPDK), 4(3), 2492–2500. https://journal.universitaspahlawan.ac.id/index.php/jpdk/article/view/5113
Friadi, J., Ganefri, R., & Efendi, R. (2020). Development of product based learning-teaching factory in the disruption era. Int. J. Adv. Sci. Technol, 29(6), 1887–1898. https://invorda.org/articles/detail/8599
Ganganahalli, P., & Udgir, R. (2024). Developing and implementing a skill-based competency module for Indian medical graduates: A community-based education approach for community diagnosis. Journal of Krishna Institute of Medical Sciences (JKIMSU), 13(1), 93. https://openurl.ebsco.com/contentitem/gcd:177331237?sid=ebsco:plink:crawler-gcd&id=ebsco:gcd:177331237&crl=c&jrnl=22314261
Guo, L., Li, P., Mao, S., Zhong, H., Zhang, Q., Zhang, R., Yan, R., & Liu, Y. (2024). Innovation and evaluation of vocational pharmaceutical education system under the 1 + X certificate system in China. Currents in Pharmacy Teaching and Learning, 16(7), 102090. https://doi.org/10.1016/j.cptl.2024.04.006
Habibu, C. O., & Malado, J. (2023). Pengembangan modul praktikum instalasi penerangan listrik di SMK Negeri 1 Talaud. JURNAL EDUNITRO Jurnal Pendidikan Teknik Elektro, 3(2), 115–126. https://doi.org/10.53682/edunitro.v3i2.6389
Härmävaara, H.-I., & Schümchen-Schram, N. (2025). How to teach know-how? Corrective manual demonstrations in teaching construction work. Language & Communication, 100, 224–242. https://doi.org/10.1016/j.langcom.2024.12.008
Hekele, F., Spilski, J., Bender, S., & Lachmann, T. (2022). Remote vocational learning opportunities—A comparative eye‐tracking investigation of educational 2D videos versus 360° videos for car mechanics. British Journal of Educational Technology, 53(2), 248–268. https://doi.org/10.1111/bjet.13162
Inayat, I., Amin, R. ul, Inayat, Z., & Salim, S. S. (2013). Effects of collaborative web based Vocational Education and Training (VET) on learning outcomes. Computers & Education, 68, 153–166. https://doi.org/10.1016/j.compedu.2013.04.027
Indriyanto, S., Permata, E., & Fatkhurrokhman, M. (2020). Pengembangan media pembelajaran trainer instalasi listrik mata pelajaran instalasi penerangan listrik. TAMAN VOKASI, 8(1), 96. https://doi.org/10.30738/jtv.v8i1.6844
Jackson, L., O’Connor, A., Paneque, M., Curtisova, V., Lunt, P. W., Pourova, R. K., Macek, M., Stefansdottir, V., Turchetti, D., Campos, M., Henneman, L., Godino, L., Skirton, H., & Cornel, M. C. (2019). The Gen-Equip Project: Evaluation and impact of genetics e-learning resources for primary care in six European languages. Genetics in Medicine, 21(3), 718–726. https://doi.org/10.1038/s41436-018-0132-3
Kiener, F., Gnehm, A.-S., Clematide, S., & Backes-Gellner, U. (2022). IT skills in vocational training curricula and labour market outcomes. Journal of Education and Work, 35(6–7), 614–640. https://doi.org/10.1080/13639080.2022.2126968
Larson, J. R., Juszczak, A., & Engel, K. (2016). Efficient vocational skills training for people with cognitive disabilities: An exploratory study comparing computer‐assisted instruction to one‐on‐one tutoring. Journal of Applied Research in Intellectual Disabilities, 29(2), 185–196. https://doi.org/10.1111/jar.12176
Lee, K., Tsai, C., Chung, C., & Lou, S. (2024). Development and validation of a high school course in refrigeration and air conditioning. International Journal of Engineering Education, 40(2), 423–439. https://ge.ntin.edu.tw/Front/Teacher_presentation_menulink_1/teacher05/Members.aspx?id=QtntyBGmS1k=&PID=0000000026
Li, X.-Z., Chen, C.-C., & Kang, X. (2022). Research on the cultivation of sustainable development ability of higher vocational students by creative thinking teaching method. Frontiers in Psychology, 13, 979913. https://doi.org/10.3389/fpsyg.2022.979913
Lochner, L., Wieser, H., Waldboth, S., & Mischo-Kelling, M. (2016). Combining traditional anatomy lectures with e-learning activities: How do students perceive their learning experience? International Journal of Medical Education, 7, 69–74. https://doi.org/10.5116/ijme.56b5.0369
Lou, M. (2017). Design of English multimedia teaching system based on diversification theory. International Journal of Emerging Technologies in Learning (IJET), 12(01), 119. https://doi.org/10.3991/ijet.v12i01.6488
Lugo, M. G. R. (2025). Enhancing technology research capacity in technical-vocational education: a participatory action research study of faculty development in Davao Oriental, Philippines. Discover Education, 4(1), 509. https://doi.org/10.1007/s44217-025-00959-9
Mahfud, T., Indartono, S., Saputro, I. N., & Utari, I. (2019). The effect of teaching quality on student career choice: The mediating role of student goal orientation. Integration of Education, 23(4), 541–555. https://doi.org/10.15507/1991-9468.097.023.201904.541-555
Nawawi, A. (2017). Perencanaan instalasi penerangan pada bangunan tempat tinggal yang aman dan efisien. Swara Patra: Majalah Ilmiah PPSDM Migas, 7(1). https://ejurnal.ppsdmmigas.esdm.go.id/sp/index.php/swarapatra/article/view/170
Nurhasanah, A., Subekti, S., & Patriasih, R. (2017). Analisis penggunan jobsheet pada praktikum dasar boga di SMKN 9 Bandung. Media Pendidikan Gizi Dan Kuliner, 9(2). https://ejournal.upi.edu/index.php/Boga/article/view/9021
Nurlaela, N., Nawi, M. Z. M., & Romadin, A. (2025). Effectiveness of e-module and learning style on self-regulation learning model to increase the occupational safety and health knowledge for mechanical education students. Journal of Technical Education and Training, 17(3), 189–203. https://doi.org/10.30880/jtet.2025.17.03.013
Peterson, D. C., & Mlynarczyk, G. S. A. (2016). Analysis of traditional versus three‐dimensional augmented curriculum on anatomical learning outcome measures. Anatomical Sciences Education, 9(6), 529–536. https://doi.org/10.1002/ase.1612
Purwati, W. antika, Sasomo, B., & Rahmawati, A. D. (2023). Analisis asesmen diagnostik pada model pembelajaran project based learning di Kurikulum Merdeka SMPN 3 Sine. Pedagogy: Jurnal Pendidikan Matematika, 8(1), 250–263. https://doi.org/10.30605/pedagogy.v8i1.2512
Putri, F., & Zakir, S. (2023). Mengukur keberhasilan evaluasi pembelajaran: Telaah evaluasi formatif dan sumatif dalam Kurikulum Merdeka. Dewantara : Jurnal Pendidikan Sosial Humaniora, 2(4), 172–180. https://doi.org/10.30640/dewantara.v2i4.1783
Ragadhita, R., Nandiyanto, A. B. D., Maryanti, R., Al Husaeni, D. F., Al Husaeni, D. N., Fiandini, M., Mudzakir, A., Hufad, A., & Masek, A. (2023). Best practice in distance learning with experimental demonstration on the concept of the automotive brake pad fabrication from domestic waste to vocational students for supporting education for sustainable development. Journal of Technical Education and Training, 15(1), 40–54. https://doi.org/10.30880/jtet.2023.15.01.005
Razali, S. S., & Bin Ismail, A. (2019). The element of fine art context in multimedia element in teaching and learning material towards motivation to learn. International Journal of Engineering and Advanced Technology, 8(6s3), 452–455. https://doi.org/10.35940/ijeat.F1082.0986S319
Rossydi, A., Wanner, P. J., Al As’ary, M., Kurnianto, B., & Fahmadi, A. E. (2026). Bridging skills and language: Developing web-based English learning platforms for vocational education. International Journal of Language Education, 10(1), 21–37. https://doi.org/10.26858/ijole.v10i1.83709
Safford, K., Cooper, D., Wolfenden, F., & Chitsulo, J. (2013). ‘Give courage to the ladies’: Expansive apprenticeship for women in rural Malawi. Journal of Vocational Education & Training, 65(2), 193–207. https://doi.org/10.1080/13636820.2012.755213
Sari, R. M., Efriyanti, L., Jasmienti, J., & Rahmat, T. (2024). Perancangan modul ajar Kurikulum Merdeka mata pelajaran informatika kelas VII di MTSN 7 Agam menggunakan Canva. JATI (Jurnal Mahasiswa Teknik Informatika), 7(6), 3802–3807. https://doi.org/10.36040/jati.v7i6.7745
Seidel, L. F., Benassi, V. A., & Lewis, J. B. (2008). The testing effect: Teaching to enhance learning in health administration education. The Journal of Health Administration Education, 25(1). https://www.proquest.com/openview/1d96f3aa964f4d9119ff7008387dc5af/1?pq-origsite=gscholar&cbl=105455
Shum, L. C., Rosunally, Y., & Munir, K. (2025). Transforming programming education: The effectiveness of motivational scenario-based design in serious games. IEEE Transactions on Education, 68(4), 394–406. https://doi.org/10.1109/TE.2025.3584187
Silor, A. C., & Silor, F. S. C. (2025). Harnessing TVET for new literacies: An experimental study on enhancing 21st century competencies. International Journal of Learning, Teaching and Educational Research, 24(11), 144–160. https://doi.org/10.26803/ijlter.24.11.7
Sinaga, J. (2019). Perancangan instalasi listrik pada rumah toko tiga lantai dengan daya 12 kw. Jurnal Teknik Elektro, 8(2), 102–112. http://jurnal.universitasdarmaagung.ac.id/teknologienergi/article/view/307
Spangenberger, P., Matthes, N., Kapp, F., Kruse, L., & Plass, J. L. (2025). Orchestrating iVR technology in an authentic classroom setting and its effects on factual knowledge, comprehension and transfer. Educational Technology Research and Development, 73(1), 387–413. https://doi.org/10.1007/s11423-024-10409-2
Star, S. L., & Griesemer, J. R. (1989). Institutional ecology,’translations,’and boundary objects: Amateurs and professionals in Berkeley’s Museum of Vertebrate Zoology, 1907–1939. Social Studies of Science, 19(3), 387–420. https://doi.org/10.1177/030631289019003001
Suartini, T. (2019). Influence application of learning model on vocational education based on quality assurance. Sage Open, 9(2), 2158244019851552. https://doi.org/10.1177/2158244019851552
Tegeh, I. M., & Jampel, I. N. (2014). Model penelitian pengembangan. Graha Ilmu.
Teresevičienė, M., Trepulė, E., & Volungevičienė, A. (2017). Didactical opportunities and dilemmas of technology enhanced learning. Pedagogika, 128(4), 175–192. https://doi.org/10.15823/p.2017.62
Tran, M., Wearne, S., Fielding, A., Moad, D., Tapley, A., Holliday, E., Ball, J., Davey, A., van Driel, M., FitzGerald, K., Spike, N., Bentley, M., Kirby, C., & Magin, P. (2023). Early-career general practitioners’ perceptions of the utility of vocational training for subsequent independent practice. Education for Primary Care, 34(2), 74–82. https://doi.org/10.1080/14739879.2023.2176264
Tuerah, R. M. S., & Tuerah, J. M. (2023). Kurikulum Merdeka dalam perspektif kajian teori: Analisis kebijakan untuk peningkatan kualitas pembelajaran di sekolah. Jurnal Ilmiah Wahana Pendidikan, 9(19), 979–988. https://www.jurnal.peneliti.net/index.php/JIWP/article/view/6937
Vygotsky, L. S. (1978). Mind in society: The development of higher psychological processes (Vol. 86). Harvard University Press.
Wells, J., Clark, K. D., & Sarno, K. (2012). A computer‐based interactive multimedia program to reduce HIV transmission for women with intellectual disability. Journal of Intellectual Disability Research, 56(4), 371–381. https://doi.org/10.1111/j.1365-2788.2011.01482.x
Wilujeng, N. G. S., & Joko, J. (2021). Analisis kelayakan pengembangan jobsheet sebagai bahan ajar peserta didik (studi literatur). Jurnal Pendidikan Teknik Elektro, 10(02), 19–26. https://doi.org/10.26740/jpte.v10n02.p19-26
Wood, D., Bruner, J. S., & Ross, G. (1976). The role of tutoring in problem solving. Journal of Child Psychology and Psychiatry, 17(2), 89–100. https://doi.org/10.1111/j.1469-7610.1976.tb00381.x
Yanto, D. T. P., Eliza, F., Ganefri, G., Sukardi, S., Hastuti, H., Kabatiah, M., & Andrian, A. (2023). Android-based courseware as an educational technology innovation for electrical circuit course: An effectiveness study. International Journal of Information and Education Technology, 13(12), 1835–1843. https://doi.org/10.18178/ijiet.2023.13.12.1996
Zhang, H., Ahmad, A. R., & Kadir, M. R. A. (2025). Impact of system quality, teaching resources, and self-motivation on independent learning: Attitudes toward MOOCs as a mediator in Guangxi. Multidisciplinary Reviews, 9(7), 2026336. https://doi.org/10.31893/multirev.2026336
Downloads
Published
How to Cite
Issue
Section
Citation Check
License
Copyright (c) 2026 Jurnal Pendidikan Vokasi
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Upon acceptance of the manuscript, the corresponding author will be required to complete and sign the Jurnal Pendidikan Vokasi Publishing Agreement before the article proceeds to publication.
The Publishing Agreement Form can be downloaded here:
Jurnal Pendidikan Vokasi Publishing Agreement
The signed agreement should be submitted electronically to the Editorial Office via email:
Authors retain the copyright of their work while granting Jurnal Pendidikan Vokasi a non-exclusive license to publish, distribute, and identify itself as the original publisher of the article.
All articles published by Jurnal Pendidikan Vokasi are licensed under the Creative Commons Attribution-ShareAlike 4.0 International License (CC BY-SA 4.0), which permits unrestricted use, distribution, adaptation, and reproduction in any medium, provided that appropriate credit is given to the original author(s), a link to the license is provided, and any derivative works are distributed under the same license.
Jurnal Pendidikan Vokasi by http://journal.uny.ac.id/index.php/jpv is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
