THE ANALYSIS OF RECIPROCATING COMPRESSOR PK 60-150 FAILURE USING FAILURE MODE AND EFFECT ANALYSIS METHOD

Nanang Qosim, Universitas Indonesia, Indonesia

 10.21831/jps.v22i2.15444

Abstract


The reciprocating compressor PK 60-150 is the most common type of compressor used in industries. The effect of each failure mode on the reciprocating compressor
was analyzed using FMEA, so that the necessary action can be determined. Both increasing the operating time and preventing the damage of compressor are
major concerns. This study was aimed to determine the problems that cause risk of safety, failure of compressor function, and shortening of compressor life time,
so that maintenance and repair cost can be reduced. The result shows that the breaking of high wires and fuses, over heat and wear of the piston are the most
affecting factors of compressor failure with RPN value of 64


Keywords


reciprocating compressor; FMEA method; failure mode; RPN

Full Text:

PDF

References


Arifi n, M. (2010). Pembuatan alat praktikum perawatan kompresor torak
ganda (Proyek Akhir). Fakultas Teknik, Universitas Sebelas Maret,
Surakarta.

Arora, R. C. (2010). Refrigeration and air conditioning. New Delhi: PHI Learning
Pvt. Ltd.

Basjir, M., Supriyanto, H., & Suef, M. (2011, Februari). Pengembangan model penentuan prioritas perbaikan terhadap mode kegagalan komponen dengan metodologi FMEA, fuzzy dan topsis yang terintegrasi. Makalah dipresentasikan pada Seminar Nasional Manajemen Teknologi XIII, ITS Surabaya.

Ben-Daya, M. (2009). Failure mode and effect analysis. Dalam M. Ben-Daya, D. AitKadi, S.O Duffuaa, J. Knezevic, & A. Raouf (Eds.), Handbook of maintenance
management and engineering (pp. 75- 90). London: Springer.

Elhaj, M., Gu, F.,Ball, A., Albarbar, A., AlQattan,M., & Naid, A. (2008). Numerical simulation and experimental study of a two-stage reciprocating compressor for condition monitoring. Mechanical Systems and Signal Processing, 22(2), 374-389.

Iswanto, A., Rambe, A. J. M., & Ginting, E. (2013). Aplikasi metode Taguchi
Analysis dan failure mode and effect analysis (FMEA) untuk perbaikan
kualitas produk di PT. XYZ. Jurnal Teknik Industri USU, 2(2).

Lubis, Y. A., & Wonoyudo, B. D. (2014). Karakteristik getaran dan efi siensi
kompresor torak akibat perubahan profi l pada valve seat sisi discharge.
Jurnal Teknik ITS, 3(1), B114-B119.

Mobley, R. K. (1999). Root cause failure analysis. Oxford: Butterworth-Heinemann.

Stamatis, D. H. (2003). Failure mode and effect analysis: FMEA from theory to
execution. Milwaukee: ASQ Quality Press.

Syawal, S., & Yusuf, M. (2011). Perencanaan kompresor piston pada tekanan kerja max 2 N/mm2. Jurnal Mesin Teknologi, 5(1).




DOI: https://doi.org/10.21831/jps.v22i2.15444

Refbacks



Bookmark and Share


Copyright (c) 2018 Jurnal Penelitian Saintek

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

 p-ISSN: 1412-3991 || e-ISSN: 2528-7036

Indexed by:

     

View My Stats