PENGEMBANGAN MODUL MATA KULIAH GAMBAR TEKNIK SEBAGAI UPAYA UNTUK MENINGKATKAN PRESTASI MAHASISWA PADA JURUSAN TEKNIK MESIN D3 IST AKPRIND YOGYAKARTA

Aji Pranoto

Abstract


This research aim to: (1) know the module development process, (2) to know the feasibility and (3) find out the effectiveness of the module to interpret engineering drawings, which have been made to support learning in interpret engineering drawings subject. The method that used in this research is research and development methods. Collection data was done by using questionnaires and test questions. The techniques of data analysis was done by using descriptive analysis techniques, by analyzing quantitative data and then interpreted in a qualitative sense. The results showed that: (1) learning module development process carried out in four main stages: needs analyze, design and creating a module, testing the feasibility and effectiveness of testing modules, (2) feasibility testing shows an average percentage value 88% with "very good" criteria and can concluded the learning interpret engineering drawings module is feasible to used for the learning process, and (3) the effectiveness testing is done by comparing the posttest experimental class value with the posttest class control value,obtained the t count value = 3.701 with the conclusion that the using of developed modules can effectively used to support learning in interpret engineering drawings subject.


Keywords


Development, Module, Engineering Drawings.

Full Text:

PDF

References


Borg, W. R. & Gall, M. D. (1983). Educational Research. An Inroduction. White Plain, New York: Longman, Inc.

Fajar Istiqomah dan Heni Purwati (2016), “ Pengembangan E-Modul Berbasis Think Pair Share (TPS) Berbantuan Flipbook Maker pada Pokok Bahasan Bangun Ruang Sisi Datar Kelas VIII”, Prosiding Seminar Nasional MASIF II 2016, Universitas PGRI Semarang.

Nasution, S. (2008). Berbagai Pendekatan dalam Proses Belajar & Mengajar. Jakarta: Bumi Aksara.

Ida sofiatun (2016),” Pengembangan E-Modul Berbantuan Flipbook Maker Pada Model Pembelajaran Jigsaw Materi Segitiga SMP Kelas VII”, Prosiding Seminar Nasional MASIF II 2016, Universitas PGRI Semarang.

Sato, Takeshi, G. dan Sugiarto, N. H. (2008). Mengmenggambar Mesin Menurut Standar ISO. Jakarta: PT Pradnya Paramita.

Sugiyono. (2010). Metode Penelitian Kuantitatif, Kualitatif dan R & D. Bandung: Alfabeta.

________. (2010). Metode Penelitian Pendidikan. Bandung: Alfabeta.

________. (2010). Statistika untuk Penelitian. Bandung: Alfabeta.

Suharsimi Arikunto. (2006). “Prosedur Penelitian Suatu Pendekatan Praktik.” Jakarta: PT Rineka Cipta.

Sukardi. (2010). “Metode Penelitian Pendidikan Kompetensi dan Praktiknya”. Jakarta: Bumi Aksara.

Vembriarto. (1976). “Pengantar Pengajaran Modul”. Yogyakarta: Yayasan Pendidikan Paramita.




DOI: https://doi.org/10.21831/jpvo.v1i2.25784

Refbacks

  • There are currently no refbacks.


Copyright (c) 2019 Jurnal Pendidikan Vokasi Otomotif

Creative Commons License
This work is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.

Creative Commons License
Jurnal Pendidikan Vokasi Otomotif is licensed under a Creative Commons Attribution-ShareAlike 4.0 International License.
Based on a work at https://journal.uny.ac.id/index.php/jpvo.

JPVO Stats