DESAIN DAN PEMBUATAN ALAT PEMBERSIH INJECTOR PORTABLE SEPEDA MOTOR BERBASIS FLASHER

Ricky Togu Firdaus Hutasoit; Ahmad Marabdi Siregar; C A Siregar

doi:10.21831/jpvo.v6i1.66000

DESAIN DAN PEMBUATAN ALAT PEMBERSIH INJECTOR PORTABLE SEPEDA MOTOR BERBASIS FLASHER

Ricky Togu Firdaus Hutasoit, Universitas Muhammadiyah Sumatera Utara
Ahmad Marabdi Siregar, Universitas Muhammadiyah Sumatera Utara, Indonesia
C A Siregar, Universitas Muhammadiyah Sumatera Utara

10.21831/jpvo.v6i1.66000

Abstract

In the motorcycle system there is a component and the Electrical Full Injection System (EFI) of this Injector component functions to inject high-pressure fuel from the common rail according to the signal given by the ECU in a Tensioner contact state or the condition of the combustion chamber engine at Timin Injection optimum, the amount of fuel injection, fuel injection ratio and fogging conditions.Two-Way Electromagnetic controls the pressure in the chamber of the injector to control the start and finish of fuel injection.Orifice in the control chamber controls the angle of opening of the nozzle to control the ratio of fuel injection.Clogging of the nozzle holes causes the effect is that the acceleration power of the motorbike engine is decreasing. this makes it difficult for motorbikes to be operational again. After cleaning the dirt that clogs the injectors in the nozzle holes, making this tool can also extend the life of the injectors.Development is a process that is used to develop and investigate a product. The test results of this tool show that the injector cleaner works well. During testing with the Vario 125 motorbike, the injector misting produced +- 35 ml/minute. If an injector produces more than 15-20 ml/minute. Then the injector is still feasible to use and use.

Keywords

Design and Development of a Flasher-Based Portable Motorcycle injector Cleaner.

Full Text:

PDF

References

Afwan, M. A., & Rahardjo, W. D. (2020). Pengaruh Penggunaan ECU Standar dan ECU Juken dengan Variasi Injektor Terhadap Torsi dan Daya Sepeda Motor Yamaha V-ixion. Automotive Science and Education Journal 9 (1) (2020), 1(2), 25–30.

Agarwal, H., Dubey, K. K., & Kamal, S. (2013). Development of Mechanical Fuel Injector Cleaning Machine in Cost Effective Manner. International Journal of Engineering and Advanced Technology (IJEAT), 2, 212. http://i21.geccdn.net/site/images/n-

Akhmadi, A. N., Usman, M. K., & Hendrawan, A. B. (2020). Analisis Kekuatan Rangka Bike Lift Terhadap Beban Alat Dan Kendaraan. Jurnal Rekayasa Material, Manufaktur Dan Energi, 3(2), 75–84. https://doi.org/10.30596/rmme.v3i2.5269

Aryadi, A. (2020). Kajian Eksperimental Pengaruh Variasi Tekanan Electric Fuel Pump Terhadap Daya, Torsi Mesin, Emisi Gas Buang Dan Konsumsi Bahan Bakar Sepeda Motor Injeksi. Teknobiz: Jurnal Ilmiah Program Studi Magister Teknik Mesin, 10(3), 55–60.

Demirbas, A., Balubaid, M. A., Basahel, A. M., Ahmad, W., & Sheikh, M. H. (2015). Octane Rating of Gasoline and Octane Booster Additives. Petroleum Science and Technology, 33(11), 1190–1197. https://doi.org/10.1080/10916466.2015.1050506

Engineering, A. (1981). International conference on manufacturing engineering. In Precision Engineering (Vol. 3, Issue 1). https://doi.org/10.1016/0141-6359(81)90079-9

Fu, C., & Gao, D. (2021). Research progress on the cathode and anode of aqueous zinc ion battry. Journal of Physics: Conference Series, 2076(1). https://doi.org/10.1088/1742-6596/2076/1/012115

Gunawan, S., Lubis, H. H., & Wanty, R. D. (2019). Jurnal Rekayasa Material , Manufaktur dan Energi FT-UMSU Jurnal Rekayasa Material , Manufaktur dan Energi FT-UMSU. Jurnal Rekayasa Material, Manufaktur Dan Energi Http://Jurnal.Umsu.Ac.Id/Index.Php/RMME, 2(2), 131–139.

Hidayat, R., Putra, D. S., & Basri, I. Y. (2019). Rancang bangun alat uji injektor berbasis mikrokontroler. Journal of Mechanical Electrical and Industrial Engineering, 35–44.

Ilham, C. I., & Sundari, E. (2023). Analysis Of Injector Flowing On Auxiliary Engine On KMP . Portlink. 5(1), 9–16.

Kaisan, M. U., Kachalla, M., Ibrahim, I. U., & Narayan, S. (2022). Comparison of camphor and fuel injector cleaner effects on the performance and emissions of gasoline engines. Journal of Engineering Research, 1–12. https://doi.org/10.36909/jer.15017

Kumar, S. R., Santhosh, S., Kumar, M. L., Aswin, V., & Gokul, B. (2022). Development of a fuel injector relative performance tester and cleaner. AIP Conference Proceedings, 2527(October). https://doi.org/10.1063/5.0108109

Mafrizal, Rukmini, & Alinsky Oyen Simbung. (2022). Analisa Menurunnya Kinerja Injektor Terhadap Proses Pembakaran Motor Diesel di Kapal MV. GOLDEN ROSE. Jurnal VENUS, 10(September), 84.

Naomi, M. M., Prima, F., Budiman, R., Studi, P., Teknik, S., Industri, J. T., Teknik, F., & Tanjungpura, U. (2017). Pemilihan Supplier Besi Siku Galvanis Menggunakan Metode Grey Theory. 195–205.

Rudi, A., Affandi, A., & Fuadi, Z. (2020). Pengaruh Cairan Pendingin Terhadap Kekasaran Permukaan Benda Kerja Pada Proses Face Milling. Jurnal Rekayasa Material, Manufaktur Dan Energi, 3(1), 16–22. https://doi.org/10.30596/rmme.v3i1.4524

Sebagai, D., Untuk, S., Gelar, M., & Teknik, S. (2017). Analisa Pengaruh Menggunakan Alat Flash Injector Pada Sepeda Motor Honda Beat Fi 110 Cc Terhadap Unjuk Kerja Mesin. 1–71.

Setyadi, P., & Setyawan, H. G. (2017). Pengaruh Kenaikan Tekanan Pompa Bahan Bakar Terhadap Performa Sepeda Motor Honda 125 Cc Injeksi Menggunakan Pompa Bahan Bakar Pneumatik. Seminar Nasional Sains Dan Teknologi FT UMJ, November, 1–2.

Siregar, M. A., & Damanik, W. S. (2020). Pengaruh Variasi Sudut Keluar Impeler Terhadap Performance Pompa Sentrifugal. Jurnal Rekayasa Material, Manufaktur Dan Energi, 3(2), 166–174. https://doi.org/10.30596/rmme.v3i2.5278

Suma’mur P.K. (2020). Implementasi Keselamatan dan Kesehatan Kerja (K3) Pada Aktivitas Fabrikasi (Pengelasan, Pemotongan, Penggerindaan) di Kota Medan. Jurnal Rekayasa Material, Manufaktur Dan Energi, 5(2), 2–2.

Urbonavičiūtė, a, Samuolienė, G., Sakalauskienė, S., Brazaitytė, a, & Tamulaitis, G. (2009). Effect of flashing amber light on the nutritional quality of green sprouts. Agronomy Research, 7(2), 761–767.

DOI: https://doi.org/10.21831/jpvo.v6i1.66000