Email this article 
Design and Development of Aluminum Frame Unmanned Aerial Vehicle Hexacopter Configuration to Support Heavy Payload
Pramudyo Wicaksono, Universitas Negeri Semarang, Indonesia
Indah Novi Yarman, Universitas Negeri Semarang, Indonesia
Abstract
Previous research has proven that the use of Unmanned Aerial Vehicles (UAVs) can increase the efficiency of human work. However, the design of the usefulness of UAV is considered to be limited. This limitation, for example, is that the UAV's lifting capacity is only capable of lifting 3-5 kilograms of load on average. In addition, the main material of the UAV frame also uses carbon fiber produced by build-up factories abroad, this makes the UAV design less economical. Furthermore, this study discusses the development of the UAV's lifting capacity of 25 kilograms to be able to lift the pesticide liquid load and considers the economic value. The hexacopter type multicopter UAV design was chosen in this study, equipped with 6 main propulsion rotors capable of carrying out its main task of lifting heavy loads, compared to the multicopter type of fewer than 6 rotors. The design is carried out by calculating the lifting force and analyzing the strength structure of the frame material with the help of AutoDesk Inventor software. The final result of the study was that the aluminum-based heavy-lift hexacopter drone was able to support heavy loads, as evidenced by structural analysis simulations resulting in a safety factor value of 1.67 ul, equipped with a 120KV rotor, 23x88 inch propeller, and 6S lipo battery 16,000 mAh, with a total weight of the frame 15kg drone flying for 19 minutes, with an additional 10kg of load the drone can fly for 6 minutes. This research can be developed by adding a nozzle or griper so that it can lift the pesticide spraying tank on a large enough agricultural land.
Keywords
Full Text:
PDFReferences
N. Ikhwana and D. R. Hapsari, “Aplikasi Drone Wawasan Tani untuk Pertanian di Simpang Lima , Sungai Besar , Selangor,” J. Pus. Inov. Masy., vol. 1, no. 1, pp. 99–104, 2019.
Nathan, E. A. Santoso, and Y. I. Jenie, “Riset Pesawat Udara Nir Awak di FTMD ITB: Pengembangan, Hasil, dan Lessons Learned,” Semin. Nas. Sains Teknol. dan Inov. Indones. (SENASTINDO AAU), vol. 1, no. 1, pp. 261–268, 2019.
A. P. Kurniawan, G. A. Mutiara, and G. I. Hapsari, “Pengiriman Informasi GPS ( Global Positioning System ) Berupa Teks Melalui Wireless pada AR Drone 2 . 0,” Univ. Telkom, vol. 1, no. 2, pp. 0–7, 2015.
R. Merkert and J. Bushell, “Managing the drone revolution: A systematic literature review into the current use of airborne drones and future strategic directions for their effective control,” J. Air Transp. Manag., vol. 89, p. 101929, 2020.
R. Vishaal, P. Raghavan, R. Rajesh, S. Michael, and M. R. Elara, “Design of Dual Purpose Cleaning Robot,” Procedia Comput. Sci., vol. 133, pp. 518–525, 2018, doi: 10.1016/j.procs.2018.07.065.
M. Saraswathi, G. B. Murali, and B. B. V. L. Deepak, “Optimal Path Planning of Mobile Robot Using Hybrid Cuckoo Search-Bat Algorithm,” Procedia Comput. Sci., vol. 133, pp. 510–517, 2018, doi: 10.1016/j.procs.2018.07.064.
I. Suroso, “Analisis Peran Unmanned Aerial Vehicle Jenis Multicopter dalam Meningkatkan Kualitas Dunia Fotografi Udara di Lokasi Jalur Selatan Menuju Calon Bandara Baru di Kulonprogo,” REKAM J. Fotogr. Telev. Animasi, vol. 14, no. 1, pp. 17–25, 2018.
I. G. M. Darmawiguna, G. S. Santyadiputra, and I. M. G. Sunarya, “Perancangan Prototipe Perangkat C-Uav (Courier Unmanned Aerial Vehicle) Berbasis Gps,” Semin. Nas. Ris. Inov., vol. 5, pp. 1–7, 2017.
M. Z. Firmansyah and P. Puspitasari, “Pemanfaatan Drone sebagai Bagian dari Kontra Terorisme,” Nakhoda J. Ilmu Pemerintah., vol. 20, no. 1, pp. 43–58, 2021, doi: 10.35967/njip.v20i1.148.
宗成庆, “Analisa Kebijakan Pengembangan Pesawat Nir-Awak ‘Unmanned Aerial Vehicle/Drone’ Sebagai Alat Kepentingan Negara Di Dunia Internasional Dalam Perspektif Hubungan Internasional,” Lemb. Penerbangan dan Antariksa Nas., pp. 98–114.
G. Macrina, L. D. P. Pugliese, F. Guerriero, and G. Laporte, “Drone-aided routing: A literature review,” Transp. Res. Part C Emerg. Technol., vol. 120, p. 102762, 2020.
J. Euchi and A. Sadok, “Hybrid genetic-sweep algorithm to solve the vehicle routing problem with drones,” Phys. Commun., vol. 44, p. 101236.
W. Bagas ardytyan, “Implementasi Sistem Telemetri Pendeteksi Musuh Pada Drone S2GA Menggunakan Sensor PIR Berbasis Arduino,” J. Tek. Elektro dan Komput. TRIAC, vol. 7, no. 1, pp. 37–39, 2020, doi: 10.21107/triac.v7i1.7418.
M. Doole, J. Ellerbroek, and J. Hoekstra, “e,” J. Air Transp. Manag., vol. 88, p. 101862, 2020.
D. Hartono and S. Darmawan, “Pemanfaatan unmanned aerial vehicle (UAV) jenis quadcopter untuk percepatan pemetaan bidang tanah (studi kasus: desa Solokan Jeruk Kabupaten Bandung),” Reka Geomatika, vol. 2018, no. 1, 2018.
R. Hidayat, “Rancang Bangun Prototype Drone Penyemprot Pestisida Untuk Pertanian Padi Secara Otomatis,” J. Mhs. Tek. Elektro, vol. 3, no. 2, pp. 86–94, 2020, [Online]. Available: http://e-jurnal.pnl.ac.id/index.php/TEKTRO/article/view/1550.
B. Y. Suprapto, M. A. Heryanto, H. Suprijono, J. Muliadi, and B. Kusumoputro, “Design and development of heavy-lift hexacopter for heavy payload,” Proc. - 2017 Int. Semin. Appl. Technol. Inf. Commun. Empower. Technol. a Better Hum. Life, iSemantic 2017, vol. 2018-Janua, no. April 2020, pp. 242–246, 2017, doi: 10.1109/ISEMANTIC.2017.8251877.
Z. Amin and D. Meldi, “Pengidentifikasian dan Pencarian Manusia Berbasis Citra Menggunakan Unmanned Aerial Vehicle,” Met. J. Sist. Mek. dan Termal, vol. 2, no. 2, p. 50, 2018, doi: 10.25077/metal.2.2.50-60.2018.
J. Clerk Maxwell, “A Treatise on Electricity and Magnetism,” Oxford: Clarendon, vol. 3rd ed., v, no. pp.68–73, pp. 31–41, 1892, doi: 10.17148/IARJSET.2018.5411.
and Y. T. Y. Yorozu, M. Hirano, K. Oka, “Electron spectroscopy studies on magneto-optical media and plastic substrate interface,” IEEE Transl. J. Magn. Japan, vol. 2, no. 1, pp. 740–741, 1987.
R. Hidayat, “Rancang Bangun Prototype Drone Penyemprot Pestisida Untuk Pertanian Padi Secara Otomatis,” J. Mhs. Tek. Elektro, vol. 3, no. 2, pp. 86–94, 2020.
Sugiyono, Metode Penelitian Bisnis: Pendekatan Kuantitatif, Kualitatif, Kombinasi, dan R&D. Bandung: CV Alfabeta, 2017.
M. Young, “The Technical Writer’s Handbook,” Mill Val., vol. 1, no. 4, pp. 192–197, 1989.
A. I. Imran and Kadir, “Simulasi Tegangan Von Mises Dan Analisa Safety Factor Gantry Crane Kapasitas 3 Ton,” vol. 8, no. 2, pp. 1–4, 2017, [Online]. Available: http://ojs.uho.ac.id/index.php/dinamika/article/view/2378.
E. J. Hearn, “Mechanics of Materials,” Mech. Mater., vol. 16, no. 1–2, 1993, doi: 10.1007/978-1-4757-1223-0_16.
DOI: https://doi.org/10.21831/elinvo.v7i1.41097
Refbacks
- There are currently no refbacks.
Copyright (c) 2022 Elinvo (Electronics, Informatics, and Vocational Education)
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Our Journal indexed by:
ISSN 2477-2399 (online) || ISSN 2580-6424 (print)
